VNH3ASP30-E
| Parameters | |
|---|---|
| Factory Lead Time | 42 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 30-MPSO, MultiPowerSO |
| Number of Pins | 30 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | STripFET™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 30 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Applications | Automotive |
| Subcategory | Motion Control Electronics |
| Technology | Power MOSFET |
| Voltage - Supply | 5.5V~16V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Supply Voltage | 9V |
| Frequency | 20kHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VNH3ASP |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Number of Outputs | 1 |
| Max Output Current | 30A |
| Supply Voltage-Min (Vsup) | 5.5V |
| Interface | PWM |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 10mA |
| Output Configuration | Half Bridge (2) |
| Collector Emitter Voltage (VCEO) | 41V |
| Max Collector Current | 30A |
| Voltage - Load | 5.5V~16V |
| Switching Frequency | 20kHz |
| Motor Type | Brushed |
| Motor Type - AC, DC | Brushed DC |
| Height | 2.25mm |
| Length | 17.3mm |
| Width | 16.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VNH3ASP30-E Overview
There is a Tubepackage included in the design.Parts are packaged in 30-MPSO, MultiPowerSOcases.Drivers controllers is recommended to mount the part by Surface Mount.The component connected in Automotiveis compatible with it.This device is capable of supplying voltages up to 5.5V~16V volts.In terms of operating temperature, it falls within the range -40°C~150°C TJ.There is a motor type Brushed DCassociated with this motor type.There are 30 terminations available on this part.If the voltage is applied to the load at the rate of [0], the load will be affected.You should run this amplifier at 9V.Surface Mountis its recommended mounting method.An analog IC with the model number BRUSH DC MOTOR CONTROLLERis employed in the device.As a result of the VNH3ASPpart number, it can be found.In this device, there are 30 pins.Drivers controllers belongs to the series [0].Currently, there are 1 outputs available.There is STripFET?, VIPower? change in the output voltage.The motor type can be identified as Brushed.For optimal operation, its maximum output current reaches [0].A frequency of 20kHzcan be achieved.
VNH3ASP30-E Features
Applications : Automotive
Load voltage across the chip 5.5V~16V
base on VNH3ASP number
designed with 1 outputs
Motor Type classified as Brushed
VNH3ASP30-E Applications
There are a lot of STMicroelectronics VNH3ASP30-E motor drivers applications.
- Camera-enabled smartphones
- Dash
- Side marker lights
- Industrial lighting
- Mobile phone display backlight and key light driving
- Footwell lighting
- Accurate LED current matching
- Commercial office
- LED bias
- Lighting for the ambience of tunability