VND10N06TR-E
| Parameters | |
|---|---|
| Factory Lead Time | 20 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Number of Pins | 3 |
| Packaging | Tape & Reel (TR) |
| Series | OMNIFET™, VIPower™ |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Resistance | 150mOhm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Power Dissipation | 35W |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 2.28mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | VND10 |
| Pin Count | 3 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 10A |
| Interface | On/Off |
| Nominal Supply Current | 150μA |
| Output Configuration | Low Side |
| Power Dissipation | 35W |
| Output Current | 6A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 150μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 10A |
| Rds On (Typ) | 150m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Length | 6.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VND10N06TR-E Overview
It's?packaged?in?the way?of?a?Tape & Reel (TR).It's included in the TO-252-3, DPak (2 Leads + Tab), SC-63 package.The mounting type of the LED driver is Surface Mount.It owns the General Purpose switch type.There are 1 outputs available on this lighting driver.Operation is based on Not Required supply voltage.There is a maximum output voltage of N-Channel volts on this LED driver.I believe it belongs to the VND10 family.As a result, there are 2 terminations.The operation is carried out using the 3 pins.It is important to note that the LED driving board has 1 functions.As a result, the maximum output current is reduced to 10A in order to meet the operation requirements.Surface Mount is mounted in the way of this LED driving board.A total of 3 pins are included in this LED driver.Lighting drivers with 150mOhm resistance are used.It is included in the OMNIFET?, VIPower? series.This case has the output current set to 6A.It requires a maximum current requirement of 150μA.
VND10N06TR-E Features
Resistance of 150mOhm
VND10N06TR-E Applications
There are a lot of STMicroelectronics VND10N06TR-E Power Switches ICs applications.
- Low Voltage I/O System Power
- Wireless Modem Data Cards
- PC Card Hot Swap
- Solid State Drivers
- Hot Swap
- HDD, SSD
- Solid-State Drives
- Notebook PC
- Hot Swap
- Telecom and Network Systems