TS5A3166DCKRE4
| Parameters | |
|---|---|
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 900mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | TS5A3166 |
| Output | SEPARATE OUTPUT |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 100nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 19 ns |
| Input Voltage (Max) | 7V |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 17.5 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 64 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 19pF 18pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 7ns, 11.5ns |
| Charge Injection | 1pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
TS5A3166DCKRE4 Overview
As the electronic part is packed in 5-TSSOP, SC-70-5, SOT-353, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. 5 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 5 pins. SPST - NO switching circuits are used in these analog switch ics. Search with TS5A3166 if you are looking for analog multiplexer variants. This digital multiplexer has 900mOhm internal resistance. The functions of 5 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. A cost-effective Single supply type analogue multiplexer. 1.65V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 10nA. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. A voltage higher than 100nA may cause damage to the switch multiplexer. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. In order to operate the 1 inputs, there are several steps to follow. The transfer of data can be performed over 200MHz bandwidths.
TS5A3166DCKRE4 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Bandwidth: 200MHz
TS5A3166DCKRE4 Applications
There are a lot of Texas Instruments TS5A3166DCKRE4 Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- FTTH
- SDH
- Microprocessor controlled systems
- RGB switches
- High speed data transmission line cards
- Fiber In The Loop (FITL)
- Fiber to the Home
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Low-Voltage