TS5A2066DCTRE4
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-LSSOP, 8-MSOP (0.110, 2.80mm Width) |
| Number of Pins | 8 |
| Weight | 23.388357mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TS5A2066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 100nA |
| Nominal Supply Current | 100nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 6.4 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 4.9 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 30nA |
| Channel Capacitance (CS(off), CD(off)) | 5.5pF 5.5pF |
| On-state Resistance Match-Nom | 0.9Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5.8ns, 3.6ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -68dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 11.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 1.3mm |
| Length | 2.95mm |
| Width | 2.8mm |
| Thickness | 1.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A2066DCTRE4 Overview
The electronic component is convenient to ship overseas because it is packed in a 8-LSSOP, 8-MSOP (0.110, 2.80mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, 8 terminations have occurred. Due to its 2 channels, the electrical component produces high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. Into the electrical component body are injected 8 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with TS5A2066 to find analog multiplexer variants. It has an internal resistance of 10Ohm. For functions related to 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Digital switch that provides Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 1.65V. 100nA current would be enough for this multiplexer to operate. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. It is possible to operate 2 inputs. It is possible to transfer data over a 300MHz-bandwidth.
TS5A2066DCTRE4 Features
2 Channels
Switch Circuit: SPST - NO
100nA Supply Current
Bandwidth: 300MHz
TS5A2066DCTRE4 Applications
There are a lot of Texas Instruments TS5A2066DCTRE4 Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- RGB switches
- DSLAMs
- Automotive applications
- Cellular phones
- Switching Systems
- PDH Multiplexers
- Microwave transmission systems
- Routers
- Avionics