TS12A4515DBVR
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | TS12A4515 |
| Output | SEPARATE OUTPUT |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Power Dissipation | 471mW |
| Max Supply Current | 50nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 120 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 475MHz |
| Turn-Off Delay Time | 80 ns |
| -3db Bandwidth | 520MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 94 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF 7.5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 45ns |
| Charge Injection | -11.5pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
TS12A4515DBVR Overview
Shipping overseas is convenient due to the electrical component's packing in SC-74A, SOT-753. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Total terminations are 5. High-quality output is provided by the electronic component's 1 channels. Powered by a 3.3V voltage supply, the electrical part should be switched on and run. A total of 5 pins are injected into the electrical part body. The analog switch ics are built using SPST - NC switching circuits. Use TS12A4515 to search for variants of the digital switches. This digital multiplexer has 20Ohm internal resistance. The functions of 5 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 2V. The analogue multiplexer could operate on 50nA current. This analog switch requires a voltage of 2.7V~12V to drain from a single voltage supply. Put voltage above 50nA on the multiplexer to cause damage. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. A 1 input needs to be operated. There are various bandwidths available for data transfer.
TS12A4515DBVR Features
1 Channels
Switch Circuit: SPST - NC
50nA Supply Current
-3db Bandwidth: 520MHz
Bandwidth: 475MHz
TS12A4515DBVR Applications
There are a lot of Texas Instruments TS12A4515DBVR Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Audio signal routing
- Channel Banks
- Video switching
- Central office
- Modems
- HDTV
- Battery Powered Systems
- Avionics and Military Systems
- E1 Multiplexer