TS12A4514DR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 15Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | TS12A4514 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 50nA |
| Power Dissipation | 471mW |
| Max Supply Current | 50nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 120 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 520MHz |
| Turn-Off Delay Time | 80 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 94 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF 7.5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 45ns |
| Charge Injection | -11.5pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS12A4514DR Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. A total of 8 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. With a 3.3V voltage supply, the electrical component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with TS12A4514. Internally, this switch multiplexer has a resistance of 15Ohm. You can find the functions of the 8 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users shouldn't supply more than 12V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. A low voltage of 2V should be applied to the electronic component. For this digital switch to work, 50nA current would suffice. This analog switch requires a voltage of 2.7V~12V to drain from a single voltage supply. If you put voltage higher than 50nA on the digital multiplexer, damage may occur. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. There are 1 inputs to be operated. A 520MHz-bandwidth can be used for data transfer.
TS12A4514DR Features
1 Channels
Switch Circuit: SPST - NO
50nA Supply Current
Bandwidth: 520MHz
TS12A4514DR Applications
There are a lot of Texas Instruments TS12A4514DR Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- CSU
- SONET/SDH ADM
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Sample-and-hold systems
- RGB switches
- Battery Powered Systems
- USB 1.1 signal switching circuits
- Video switching