TPS2010DR
| Parameters | |
|---|---|
| Lifecycle Status | NRND (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 75mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TPS2010 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 200mA |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Interface | On/Off |
| Analog IC - Other Type | POWER SUPPLY SUPPORT CIRCUIT |
| Nominal Supply Current | 73μA |
| Output Configuration | High Side |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 73μA |
| Adjustable Threshold | NO |
| Quiescent Current | 73μA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Min Current Limit | 220mA |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 75m Ω |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TPS2010DR Overview
The LED driver's packaged as a Tape & Reel (TR).It is included with the 8-SOIC (0.154, 3.90mm Width) package as well.Mounting type Surface Mount is selected for the LED driving board.The switch type of this switch is General Purpose.To ensure reliable operation, set the temperature to -40°C~125°C TJ.The lighting driver has a total of 1 outputs that are available for use.In order to operate, it requires a voltage supply of Not Required.A maximum voltage of N-Channel volts is available from the output of this LED driver.It is a member of the TPS2010 family.As a result, there are 8 terminations.It is necessary to use the 8 pins in order to operate the LED driver.As far as the lighting driver is concerned, there are 1 functions.This results in the maximum output current dropping to 200mA to meet the operation criteria.High efficiency is possible at 3V supply voltage.The LED driving board is equipped with a total of 8 pins.There is 75mOhm resistance on the LED driver.The output current is set to 200mA in this case.In this case, a digital IC is used, which is POWER SUPPLY SUPPORT CIRCUIT.In total, there are 1 channels available.In order to optimize the efficiency of the supply voltage, it should be set to 5.5V.The maximum input voltage of the LED driver is 5.5V volts.The minimum input voltage is 2.7V volts.A maximum current requirement of 73μA is required for its operation.
TPS2010DR Features
Supplied from 3V
Resistance of 75mOhm
1 channels
TPS2010DR Applications
There are a lot of Texas Instruments TPS2010DR Power Switches ICs applications.
- USB Protection
- USB Power Distribution
- USB3.1 Power Delivery
- Wearable Devices
- Hot Swap
- Portable/Handheld Devices
- Hot Swaps
- Portable GPS Device
- Hot-Swap Systems
- Gaming