TLE9879QXA40XUMA2
| Parameters | |
|---|---|
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 13.5V |
| Terminal Pitch | 0.5mm |
| Frequency | 40MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Interface | LIN, SSI, UART |
| Memory Size | 128kB |
| Number of I/O | 10 |
| Nominal Supply Current | 30mA |
| RAM Size | 6K x 8 |
| Memory Type | FLASH |
| uPs/uCs/Peripheral ICs Type | MICROCONTROLLER, RISC |
| Core Processor | ARM® Cortex®-M3 |
| Program Memory Type | FLASH (128kB) |
| Bit Size | 32 |
| Watchdog Timer | Yes |
| Has ADC | YES |
| DMA Channels | YES |
| Data Bus Width | 32b |
| PWM Channels | YES |
| Halogen Free | Halogen Free |
| Number of Timers/Counters | 4 |
| Core Architecture | ARM |
| On Chip Program ROM Width | 8 |
| Number of A/D Converters | 2 |
| Number of ADC Channels | 1 |
| Max Junction Temperature (Tj) | 150°C |
| Height | 900μm |
| Length | 7mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 26 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-VFQFN Exposed Pad |
| Number of Pins | 48 |
| Operating Temperature | -40°C~150°C |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 48 |
| Applications | Automotive |
| Technology | CMOS |
| Voltage - Supply | 5.5V~28V |
TLE9879QXA40XUMA2 Features
32 bit ARM Cortex M3 Core
– up to 40 MHz clock frequency
– one clock per machine cycle architecture
On-chip memory
– 128 kByte Flash including
– 4 kByte EEPROM (emulated in Flash)
– 512 Byte 100 Time Programmable Memory (100TP)
– 6 kByte RAM
– Boot ROM for startup firmware and Flash routines
On-chip OSC and PLL for clock generation
– PLL loss-of-lock detection
MOSFET driver including charge pump
10 general-purpose I/O Ports (GPIO)
5 analog inputs, 10-bit A/D Converter (ADC1)
16-bit timers - GPT12, Timer 2, Timer 21 and Timer 3
Capture/compare unit for PWM signal generation (CCU6)
2 full duplex serial interfaces (UART) with LIN support (for UART1 only)
2 synchronous serial channels (SSC)
On-chip debug support via 2-wire SWD
1 LIN 2.2 transceiver
1 high voltage monitoring input
Single power supply from 5.5 V to 27 V
Extended power supply voltage range from 3 V to 28 V
Low-dropout voltage regulators (LDO)
High speed operational amplifier for motor current sensing via shunt
5 V voltage supply for external loads (e.g. Hall sensor)
Core logic supply at 1.5 V
Programmable window watchdog (WDT1) with independent on-chip clock source
Power saving modes
– MCU slow-down Mode
– Sleep Mode
– Stop Mode
– Cyclic wake-up Sleep Mode
Power-on and undervoltage/brownout reset generator