SN74LVTH273PWRG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 150MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 3.3V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.7V |
| Load Capacitance | 50pF |
| Current - Output | 64mA |
| Propagation Delay | 3.2 ns |
| Turn On Delay Time | 3.2 ns |
| Family | LVT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| Prop. Delay@Nom-Sup | 4.9 ns |
| High Level Output Current | -32mA |
| Low Level Output Current | 64mA |
| Power Supply Current-Max (ICC) | 5mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74LVTH273PWRG4 Overview
TSSOPis the way it is packaged. It is contained within the Tape & Reel (TR)package. There is a TTLoutput configured with it. D latch consists of 1 elements. There have been 20 terminations. The power source is powered by 3.3V. It belongs to the family of electronic devices known as LVT. It is mounted by the way of Surface Mount. The electronic flip flop is designed with pins 20. This device's clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. In view of its reliability, this D flip flop is a good fit for TR. High efficiency requires the supply voltage to be maintained at 3.3V. A high level output current of -32mAis set. There is 64mA output current at the low level. Ideally, the operating temperature should be below 85°C. It is recommended that the operating temperature is higher than -40°C. The minimal supply voltage is 2.7V. 3.6Vis the maximum supply voltage supported by it. It is possible to achieve 150MHz frequencies. The logic IC it uses is D FLIP-FLOP. There are 1 functions available on this T flip flop. It is equipped with 20 pins. The 64mA output current allows it to be designed with the greatest amount of flexibility.
SN74LVTH273PWRG4 Features
Tape & Reel (TR) package
20 pins
1 Functions
20 pin count
SN74LVTH273PWRG4 Applications
There are a lot of Texas Instruments SN74LVTH273PWRG4 Flip Flops applications.
- Matched Rise and Fall
- ESD performance
- Computers
- Consumer
- Circuit Design
- Single Down Count-Control Line
- Event Detectors
- Count Modes
- Dynamic threshold performance
- Frequency Divider circuits