SN74LVC1G66YEPR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-XFBGA, DSBGA |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LVC1G66 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.2 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 42 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 6pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 4.2ns, 5ns |
| Switch-off Time-Max | 6.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74LVC1G66YEPR Overview
Shipping overseas is convenient with the electronic component packed in 5-XFBGA, DSBGA. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. Totally, there are 5 terminations. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 2.3V volts, the electrical part can be powered up and run. A total of 5 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPST - NO switching circuits. There are 1 circuits in this switch device. Try searching with 74LVC1G66 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the 5 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 1.65V. For this digital switch to work, 10μA current would suffice. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 10μA.
SN74LVC1G66YEPR Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 300MHz
SN74LVC1G66YEPR Applications
There are a lot of Texas Instruments SN74LVC1G66YEPR Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Multiplexers
- Industrial control systems
- Channel Banks
- Sample-and-hold systems
- Industrial and process control systems
- DSLAMs
- E1 Network Equipment
- ISDN NT1/TA
- Microprocessor controlled systems