SN74LS173ADR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LS |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Additional Feature | WITH HOLD MODE; WITH DUAL OUTPUT ENABLE; DISABLE TIME CL = 5PF |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74LS173 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Output Current | 24mA |
| Clock Frequency | 50MHz |
| Propagation Delay | 30 ns |
| Turn On Delay Time | 28 ns |
| Family | LS |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 2.6mA 24mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 25ns @ 5V, 45pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 2 |
| fmax-Min | 30 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
SN74LS173ADR Overview
16-SOIC (0.154, 3.90mm Width)is the packaging method. It is contained within the Tape & Reel (TR)package. T flip flop uses Tri-State, Non-Invertedas the output. The trigger it is configured with uses Positive Edge. Surface Mountis in the way of this electric part. With a supply voltage of 4.75V~5.25V volts, it operates. A temperature of 0°C~70°C TAis used in the operation. This electronic flip flop is of type D-Type. In terms of FPGAs, it belongs to the 74LS series. It should not exceed 50MHzin terms of its output frequency. A total of 1 elements are present. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. You can search similar parts based on 74LS173. A voltage of 5V provides power to the D latch. In terms of electronic devices, this device belongs to the LSfamily of devices. The electronic part is mounted in the way of Surface Mount. A total of 16pins are provided on this board. Its clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. A total of 5V power supplies are needed to run it. The 24mA output current allows it to be designed with the greatest amount of flexibility. There are 2 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. Additionally, there are WITH HOLD MODE; WITH DUAL OUTPUT ENABLE; DISABLE TIME CL = 5PF on the electronic flip flop that can be referred to.
SN74LS173ADR Features
Tape & Reel (TR) package
74LS series
16 pins
5V power supplies
SN74LS173ADR Applications
There are a lot of Texas Instruments SN74LS173ADR Flip Flops applications.
- Automotive
- Safety Clamp
- Dynamic threshold performance
- Convert a momentary switch to a toggle switch
- Test & Measurement
- Event Detectors
- ESCC
- Data transfer
- Shift registers
- Buffered Clock