SN74HC112DRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 2 |
| Propagation Delay | 125 ns |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | AND, JK-Type |
| Logic IC Type | J-K FLIP-FLOP |
| Max I(ol) | 0.004 A |
| High Level Output Current | 5.2mA |
| Low Level Output Current | 4mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Negative Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HC112DRG4 Overview
The flip flop is packaged in a case of SOIC. The package Tape & Reel (TR)contains it. A total of 2 elements are present. Currently, there are 16 terminations. Power is provided by a 5V supply. The electronic device belongs to the HC/UHfamily. Electronic part Surface Mountis mounted in the way. The 16pins are designed into the board. This device exhibits a clock edge trigger type of Negative Edge. It is part of the FF/Latchesbase part number family. There are 2bits in this flip flop. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. The supply voltage should be maintained at 5V for high efficiency. It has 1 output lines to operate. 5.2mAis set as the high level output current. There is no low level output current set at 4mA. A temperature below 85°Cshould be used for operation. It should be higher than -40°Cwhen the system is operating. Normally, it operates with a voltage of 2VV as its minimum supply voltage. A maximum voltage of 6V can be provided by it. We are able to achieve a frequency of 60MHz. The logic IC it uses is J-K FLIP-FLOP. A total of 2 functions are available on the T flip flop. The D latch is equipped with 16 pins. The output current of 5.2mA makes it feature maximum design flexibility.
SN74HC112DRG4 Features
Tape & Reel (TR) package
16 pins
2 Bits
2 Functions
16 pin count
SN74HC112DRG4 Applications
There are a lot of Texas Instruments SN74HC112DRG4 Flip Flops applications.
- Common Clocks
- Modulo – n – counter
- Functionally equivalent to the MC10/100EL29
- Digital electronics systems
- Count Modes
- Synchronous counter
- Guaranteed simultaneous switching noise level
- Reduced system switching noise
- Patented noise
- ATE