SN74F112DRE4
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 20mA |
| Number of Bits | 2 |
| Propagation Delay | 6.5 ns |
| Turn On Delay Time | 4.6 ns |
| Family | F/FAST |
| Logic Function | AND, Flip-Flop, JK-Type |
| Logic IC Type | J-K FLIP-FLOP |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Negative Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latch |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Frequency | 130MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
SN74F112DRE4 Overview
The item is packaged in SOICcases. The package Tape & Reel (TR)contains it. It is configured with TTLas an output. D latch consists of 2 elements. Currently, there are 16 terminations. A voltage of 5V is used as the power supply for this D latch. F/FASTis the family of this D flip flop. A part of the electronic system is mounted in the way of Surface Mount. As you can see from the design, it has pins with 16. This device exhibits a clock edge trigger type of Negative Edge. This RS flip flops is a part number FF/Latch. Flip flops designed with 2bits are used in this part. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. The D latch operates on 5V volts. For high efficiency, the supply voltage should be kept at 5V. It is designed with 1 output lines. -1mAis the output current at high level. 20mAis set as the low level output current. Operating temperatures should be lower than 70°C. It is recommended that the operating temperature be greater than 0°C. In order for it to operate, a supply voltage of 4.5Vis required. There is a maximum voltage support of 5.5V. The frequency that can be achieved is 130MHz. There is a logic IC J-K FLIP-FLOP used in the D flip flop. There are 2 functions available on this T flip flop. With 16 pins, it is equipped with a low power consumption. It offers maximum design flexibility with its output current of 20mA.
SN74F112DRE4 Features
Tape & Reel (TR) package
16 pins
2 Bits
5V power supplies
2 Functions
16 pin count
SN74F112DRE4 Applications
There are a lot of Texas Instruments SN74F112DRE4 Flip Flops applications.
- Differential Individual
- Power down protection
- Safety Clamp
- Parallel data storage
- Circuit Design
- Count Modes
- Buffer registers
- Matched Rise and Fall
- Shift Registers
- Consumer