SN74BCT574DWR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74BCT |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74BCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 77MHz |
| Propagation Delay | 8.6 ns |
| Turn On Delay Time | 6.5 ns |
| Family | BCT/FBT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8mA |
| Current - Output High, Low | 15mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 8.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5.5pF |
| Power Supply Current-Max (ICC) | 62mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 77000000Hz |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74BCT574DWR Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. D flip flop is embedded in the Tape & Reel (TR) package. This output is configured with Tri-State, Non-Inverted. This trigger uses the value Positive Edge. Surface Mountis occupied by this electronic component. A supply voltage of 4.5V~5.5V is required for operation. It is operating at 0°C~70°C TA. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74BCTseries of FPGAs. Its output frequency should not exceed 77MHz Hz. The list contains 1 elements. Despite external influences, it consumes 8mAof quiescent current. Terminations are 20. D latch belongs to the 74BCT574 family. It is powered by a voltage of 5V . Its input capacitance is 5.5pF farads. BCT/FBTis the family of this D flip flop. It is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. There is a clock edge trigger type of Positive Edgeon this device. The part is included in FF/Latches. The flip flop is designed with 8bits. Despite its superior flexibility, it relies on 8 circuits to achieve it. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 5V power supplies are needed to run it. This flip flop has a total of 2ports. For high efficiency, the supply voltage should be kept at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 64mA. The JK flip flop is with 3 output lines to operate.
SN74BCT574DWR Features
Tape & Reel (TR) package
74BCT series
20 pins
8 Bits
5V power supplies
SN74BCT574DWR Applications
There are a lot of Texas Instruments SN74BCT574DWR Flip Flops applications.
- Load Control
- Safety Clamp
- Data storage
- Memory
- Differential Individual
- Functionally equivalent to the MC10/100EL29
- Data transfer
- Test & Measurement
- Communications
- Reduced system switching noise