SN74AUC2G53YZTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFBGA, DSBGA |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 15Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.1V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74AUC2G53 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 2.7V |
| Min Supply Voltage | 800mV |
| Operating Supply Current | 10μA |
| Max Supply Current | 10μA |
| Turn On Delay Time | 9.2 ns |
| Supply Type | Single |
| Bandwidth | 198MHz |
| Turn-Off Delay Time | 8.1 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 15Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 59 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 2.2ns, 2.3ns |
| Channel-to-Channel Matching (ΔRon) | 1 Ω (Max) |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 3.6ns |
| Switch-off Time-Max | 4.2ns |
| Voltage - Supply, Single (V+) | 0.8V~2.7V |
| Height Seated (Max) | 0.625mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
SN74AUC2G53YZTR Overview
Packed in 8-UFBGA, DSBGA, the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 2:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 8 terminations. This electronic part offers high-quality output due to its 2 channels. A 1.1V voltage supply should turn on and run the electronic component. An electrical component of this type can be found in the 8 series. Based on SPDT switching circuits, these analog multiplexers work. It consists of 1 circuits. Search with 74AUC2G53 if you are looking for analog multiplexer variants. A 15Ohm internal resistance characterizes this multiplexer. To find out what the 8 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 2.7V in normal situations. The analog switch ic is of the Single supply type and is cost-effective. 800mV should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 10μA current would be sufficient. A voltage of 0.8V~2.7V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 10μA on the multiplexer may cause damage. It is possible to transfer data over a 198MHz-bandwidth.
SN74AUC2G53YZTR Features
2 Channels
Switch Circuit: SPDT
10μA Supply Current
-3db Bandwidth: 50MHz
Bandwidth: 198MHz
SN74AUC2G53YZTR Applications
There are a lot of Texas Instruments SN74AUC2G53YZTR Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Access Concentrators
- Data Acquisition Systems
- USB 1.1 signal switching circuits
- Audio and video routing
- MP3 players
- SONET/SDH ADM
- Fiber In The Loop (FITL)
- Precision data acquisition
- Relay replacements