SN74AS175BNSR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Weight | 200.686274mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AS175 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 20mA |
| Clock Frequency | 100MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 3 ns |
| Family | AS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 34mA |
| Current - Output High, Low | 2mA 20mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AS175BNSR Overview
The item is packaged in 16-SOIC (0.209, 5.30mm Width)cases. As part of the package Tape & Reel (TR), it is embedded. Currently, the output is configured to use Differential. JK flip flop uses Positive Edgeas the trigger. It is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. 0°C~70°C TAis the operating temperature. It belongs to the type D-Typeof flip flops. In FPGA terms, D flip flop is a type of 74ASseries FPGA. In order for it to function properly, its output frequency should not exceed 100MHz. A total of 1elements are present in it. During its operation, it consumes 34mA quiescent energy. It has been determined that there have been 16 terminations. You can search similar parts based on 74AS175. Power is provided by a 5V supply. It belongs to the family of electronic devices known as AS. It is mounted in the way of Surface Mount. This board is designed with 16pins on it. This device's clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. Its superior flexibility is attributed to its use of 7 circuits. This D flip flop is well suited for TR based on its reliable performance. A total of 5V power supplies are needed to run it. If high efficiency is desired, the supply voltage should be kept at 5V. The 20mA output current allows it to be designed with the greatest amount of flexibility. There are 2 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. This input has 3lines in it.
SN74AS175BNSR Features
Tape & Reel (TR) package
74AS series
16 pins
5V power supplies
SN74AS175BNSR Applications
There are a lot of Texas Instruments SN74AS175BNSR Flip Flops applications.
- Individual Asynchronous Resets
- Convert a momentary switch to a toggle switch
- Bounce elimination switch
- Consumer
- Matched Rise and Fall
- Shift registers
- Single Up Count-Control Line
- Modulo – n – counter
- Balanced 24 mA output drivers
- Common Clocks