SN74AHCT374DW
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT374DW Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. The package Tubecontains it. Currently, the output is configured to use Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. In this case, the operating temperature is -40°C~85°C TA. This D latch has the type D-Type. FPGAs belonging to the 74AHCTseries contain this type of chip. Its output frequency should not exceed 130MHz Hz. In total, it contains 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. If you search by 74AHCT374, you will find similar parts. Power is supplied from a voltage of 5V volts. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of AHCT/VHCT/VT. There is an electronic component mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. This device has the clock edge trigger type of Positive Edge. The RS flip flops belongs to FF/Latches base part number. It is designed with a number of bits of 8. 8 circuits are used to achieve its superior flexibility. It operates from 5V power supplies. There are 2 ports embedded in the flip flops. Optimal efficiency requires a supply voltage of 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 8mA. It is reported that there are 3 input lines.
SN74AHCT374DW Features
Tube package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT374DW Applications
There are a lot of Texas Instruments SN74AHCT374DW Flip Flops applications.
- Individual Asynchronous Resets
- Instrumentation
- EMI reduction circuitry
- Latch-up performance
- ESCC
- Guaranteed simultaneous switching noise level
- Bounce elimination switch
- Set-reset capability
- Divide a clock signal by 2 or 4
- Parallel data storage