SN74AHCT16374DL
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 48 |
| Weight | 600.301152mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 16 |
| Clock Frequency | 130MHz |
| Propagation Delay | 10.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 11.5 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2.79mm |
| Length | 15.88mm |
| Width | 7.49mm |
| Thickness | 2.59mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT16374DL Overview
The flip flop is packaged in 48-BSSOP (0.295, 7.50mm Width). Package Tubeembeds it. In the configuration, Tri-State, Non-Invertedis used as the output. It is configured with a trigger that uses Positive Edge. Surface Mountis positioned in the way of this electronic part. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. In the operating environment, the temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74AHCT series. You should not exceed 130MHzin its output frequency. The element count is 2 . This process consumes 4μA quiescents. There have been 48 terminations. If you search by 74AHCT16374, you will find similar parts. A voltage of 5V provides power to the D latch. The input capacitance of this T flip flop is 2.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. AHCT/VHCT/VTis the family of this D flip flop. There is an electronic part that is mounted in the way of Surface Mount. 48pins are included in its design. A Positive Edgeclock edge trigger is used in this device. There is a base part number FF/Latchesfor the RS flip flops. The design is based on 16bits. It operates from 5V power supplies. This flip flop has a total of 2ports. For high efficiency, the supply voltage should be set to 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 8mA. The JK flip flop is with 3 output lines to operate.
SN74AHCT16374DL Features
Tube package
74AHCT series
48 pins
16 Bits
5V power supplies
SN74AHCT16374DL Applications
There are a lot of Texas Instruments SN74AHCT16374DL Flip Flops applications.
- Frequency Dividers
- Cold spare funcion
- Count Modes
- Frequency Divider circuits
- Clock pulse
- Digital electronics systems
- Circuit Design
- Single Down Count-Control Line
- Divide a clock signal by 2 or 4
- QML qualified product