SN74AHC74D
| Parameters | |
|---|---|
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 6.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AHC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Clock Frequency | 115MHz |
| Propagation Delay | 15.4 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | AND, D-Type, Flip-Flop |
SN74AHC74D Overview
It is packaged in the way of 14-SOIC (0.154, 3.90mm Width). It is included in the package Tube. It is configured with Differentialas an output. In the configuration of the trigger, Positive Edgeis used. There is an electronic component mounted in the way of Surface Mount. The supply voltage is set to 2V~5.5V. It is at -40°C~125°C TAdegrees Celsius that the system is operating. It is an electronic flip flop with the type D-Type. It belongs to the 74AHCseries of FPGAs. It should not exceed 115MHzin terms of its output frequency. It consumes 2μA of quiescent current without being affected by external factors. There are 14 terminations,JK flip flop belongs to 74AHC74 family. A voltage of 3.3V is used as the power supply for this D latch. Its input capacitance is 2pF farads. The electronic device belongs to the AHC/VHC/H/U/Vfamily. In this case, the electronic component is mounted in the way of Surface Mount. As you can see from the design, it has pins with 14. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. It reaches the maximum supply voltage (Vsup) at 5.5V. Normal operation requires a supply voltage (Vsup) above 2V. As a result of its output current of 8mA, it is very flexible in terms of design. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. It is reported that there are 2 channels.
SN74AHC74D Features
Tube package
74AHC series
14 pins
SN74AHC74D Applications
There are a lot of Texas Instruments SN74AHC74D Flip Flops applications.
- Data Synchronizers
- Count Modes
- Buffered Clock
- Consumer
- Power down protection
- Parallel data storage
- Storage Registers
- Supports Live Insertion
- Differential Individual
- Common Clocks