SN74AHC273PW
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 17.1 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC273PW Overview
20-TSSOP (0.173, 4.40mm Width)is the way it is packaged. It is contained within the Tubepackage. It is configured with Non-Invertedas an output. Positive Edgeis the trigger it is configured with. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at 2V~5.5Vvolts. In this case, the operating temperature is -40°C~125°C TA. D-Typedescribes this flip flop. FPGAs belonging to the 74AHCseries contain this type of chip. There should be no greater frequency than 110MHzon its output. There are 1 elements in it. T flip flop consumes 4μA quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74AHC273family includes it. A voltage of 3.3V is used as the power supply for this D latch. A 2.5pFfarad input capacitance is provided by this T flip flop. This D flip flop belongs to the family of AHC/VHC/H/U/V. Electronic part Surface Mountis mounted in the way. As you can see from the design, it has pins with 20. This device has Positive Edgeas its clock edge trigger type. The RS flip flops belongs to FF/Latches base part number. The design is based on 8bits. There is a 5.5Vmaximum supply voltage (Vsup). Normal operation requires a supply voltage (Vsup) above 2V. The superior flexibility is achieved through the use of 8 circuits. A total of 2/5.5V power supplies are needed to run it. As a result of its output current of 8mA, it is very flexible in terms of design. It has 3lines.
SN74AHC273PW Features
Tube package
74AHC series
20 pins
8 Bits
2/5.5V power supplies
SN74AHC273PW Applications
There are a lot of Texas Instruments SN74AHC273PW Flip Flops applications.
- Balanced Propagation Delays
- Circuit Design
- Digital electronics systems
- 2 – Bit synchronous counter
- Bounce elimination switch
- Data transfer
- Communications
- Differential Individual
- Pattern generators
- Load Control