SN74AC374PWRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 155MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 13.5 ns |
| Turn On Delay Time | 8 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AC374PWRE4 Overview
The package is in the form of TSSOP. It is included in the package Tape & Reel (TR). 20terminations have occurred. It is powered by a voltage of 3.3V . The electronic device belongs to the ACfamily. A part of the electronic system is mounted in the way of Surface Mount. A total of 20pins are provided on this board. A Positive Edgeclock edge trigger is used in this device. There is a base part number FF/Latchesfor the RS flip flops. An electronic part designed with 8bits is used in this application. 8 circuits are used to achieve its superior flexibility. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It has 1 output lines to operate. Currently, there are 3 input lines present. There is -24mA output current at the high level. There is 24mA output current at the low level. Operating temperatures should be lower than 85°C. If the operating temperature is higher than -40°C, the system should operate properly. The RS flip flop is designed to operate with a minimal supply voltage of 2VV. It supports a maximum supply voltage of 6V volts. This frequency can be achieved 155MHz. The logic IC it uses is BUS DRIVER. It is equipped with 1 Functions . This device is equipped with a pin count of 20. It features maximum design flexibility due to the 24mA output current.
SN74AC374PWRE4 Features
Tape & Reel (TR) package
20 pins
8 Bits
1 Functions
20 pin count
SN74AC374PWRE4 Applications
There are a lot of Texas Instruments SN74AC374PWRE4 Flip Flops applications.
- Counters
- ESCC
- Consumer
- Count Modes
- EMI reduction circuitry
- Latch-up performance
- Balanced Propagation Delays
- ESD protection
- Parallel data storage
- Bus hold