PI3A268CZMEX
| Parameters | |
|---|---|
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 50ns |
| Charge Injection | 52pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -80dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 85ns |
| Switch-off Time-Max | 85ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height Seated (Max) | 0.55mm |
| Length | 1.8mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 20 Weeks |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 400mOhm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | PI3A268 |
| Output | SEPARATE OUTPUT |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 500nA |
| Supply Type | Single |
| -3db Bandwidth | 85MHz |
| On-State Resistance (Max) | 400mOhm Typ |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 21pF |
| On-state Resistance Match-Nom | 0.1Ohm |
PI3A268CZMEX Overview
Packed in 10-UFQFN, the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. The total number of terminations is 10. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 2.7V volts, the electrical part can be powered up and run. Multiplexers built on a SPDT switching circuit are built. There are 2 circuits in this switch device. Use PI3A268 to search for variants of the digital switches. A 400mOhm internal resistance characterizes this multiplexer. Datasheets for 10 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 4.3V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. The switch device would be able to operate with 500nA current. Analogue multiplexers require a 1.65V~4.3V voltage to drain from a single voltage supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. It can operate from 3V operating voltages.
PI3A268CZMEX Features
1 Channels
Switch Circuit: SPDT
500nA Supply Current
-3db Bandwidth: 85MHz
PI3A268CZMEX Applications
There are a lot of Diodes Incorporated PI3A268CZMEX Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Signal routing between systems
- Sample-and-hold systems
- E1 Multiplexer
- Cable Modem
- Residential Gateways, Home Gateway/Router
- Communication systems
- PBX interfaces
- Audio and video switching
- Relay replacements