OPA2350UAG4
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 75.891673mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | OPA2350 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Elements | 2 |
| Operating Supply Current | 5.2mA |
| Nominal Supply Current | 15mA |
| Slew Rate | 22V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 74 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 38MHz |
| Unity Gain BW-Nom | 38000 kHz |
| Voltage Gain | 122dB |
| Average Bias Current-Max (IIB) | 0.00001μA |
| Power Supply Rejection Ratio (PSRR) | 87.96dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 150μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 1mV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA2350UAG4 Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. Buffer amps of this type are called General Purpose-types. In the case of Tube cases, linear amplifier will be delivered. The number of terminations approaches 8. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 8 pins. In terms of the input offset voltage, instrumentation amplifier rates at 500μV. This electrical part should be mounted using type Surface Mount. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. The buffer amplifier is capable of operating from a supply current of 5.2mA . Maintain 122dB as the voltage gain. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. Op amp has total of 2 elements. Instrumentation amplifiers are numbered by their MicroAmplifier? series.
OPA2350UAG4 Features
8 Pins
supply voltage of 5V
122dB voltage gain
Output Type: Rail-to-Rail
OPA2350UAG4 Applications
There are a lot of Texas Instruments OPA2350UAG4 Instrumentational OP Amps applications.
- Communication
- Signal operation
- Radar
- Laptop
- Gaming industry
- E-book readers
- Band-pass filter
- PDA
- Division circuits
- Industrial applications including automation