NLVASB3157DFT2G
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 7Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexers or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.4mm |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 10μA |
| Power Dissipation | 180mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 5.7 ns |
| Number of Inputs | 1 |
| Halogen Free | Halogen Free |
| Turn-Off Delay Time | 3.8 ns |
| -3db Bandwidth | 250MHz |
| On-State Resistance (Max) | 7Ohm Typ |
| High Level Output Current | 128mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -54dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 1mm |
| Length | 2.2mm |
| Width | 1.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
NLVASB3157DFT2G Overview
Presented in 6-TSSOP, SC-88, SOT-363, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. An extended operating temperature of -55°C~125°C TA degrees Celsius. In total, there are 6 terminations. The electronic part provides high-quality output because it has 2 channels. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. Into the electrical component body are injected 6 pins. Based on SPDT switching circuits, these analog multiplexers work. The internal resistance of this digital multiplexer is 7Ohm. To find out what the 6 pins do, please refer to the datasheets. It is a typical Multiplexers or Switches analog multiplexer. Multiplexers should not be powered above 5.5V in normal situations. A low voltage of 1.65V should be applied to the electronic component. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 10μA. Operating the 1 inputs requires 1 inputs. The analogue multiplexer has 2 outputs.
NLVASB3157DFT2G Features
2 Channels
Switch Circuit: SPDT
-3db Bandwidth: 250MHz
NLVASB3157DFT2G Applications
There are a lot of ON Semiconductor NLVASB3157DFT2G Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Microwave transmission systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Residential Gateways, Home Gateway/Router
- Public switching systems
- Avionics
- Channelized and Unchannelized DS3 applications
- Precision test equipment
- Wireless Local Loop
- Relay replacements