NLAS4599DFT2
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 30Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 200mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLAS4599 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Turn On Delay Time | 28 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 220MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 8ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLAS4599DFT2 Overview
Shipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. The operating temperature is extended to around -55°C~125°C TA. In total, there have been 6 terminations. A electrical component with 2 channels is capable of high-quality output. An 4.5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 6 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used to build these analog multiplexers. It consists of 1 circuits. Search with NLAS4599 if you are looking for analog multiplexer variants. It has an internal resistance of 30Ohm. For functions related to 6 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 1μA current. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. The electrical part can be operated at 5V voltage levels.
NLAS4599DFT2 Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 220MHz
NLAS4599DFT2 Applications
There are a lot of ON Semiconductor NLAS4599DFT2 Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- CSU
- Modems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- High speed data transmission line cards
- E1 Multiplexer
- 65 V DACs
- Industrial control systems
- MP3 players
- Remote Powered Equipment