NLAS2066US
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Surface Mount | YES |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Terminal Finish | TIN LEAD |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | COMMERCIAL |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 186MHz |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| On-state Resistance Match-Nom | 1.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3ns, 6ns |
| Charge Injection | 7.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Switch-on Time-Max | 9ns |
| Switch-off Time-Max | 10ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height Seated (Max) | 0.9mm |
| RoHS Status | Non-RoHS Compliant |
NLAS2066US Overview
Due to its 8-VFSOP (0.091, 2.30mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -55°C~125°C TA extended. 8 terminations have been made so far. A 1 channel electronic part produces high-quality output. When a voltage supply of 2.3V is used, the electronic component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. SPST - NO switching circuits are used in these analog switch ics. Circuits number 2 make up this analogue multiplexer. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply.
NLAS2066US Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 186MHz
NLAS2066US Applications
There are a lot of Rochester Electronics, LLC NLAS2066US Analog Switches & Multiplexers ICs applications.
- Communication systems
- Automotive applications
- Avionics and Military Systems
- HDTV
- Remote Powered Equipment
- Audio and video routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cell phones
- PDAs
- USB 1.1 signal switching circuits