Parameters |
Factory Lead Time |
4 Weeks |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-SOIC (0.295, 7.50mm Width) |
Number of Pins |
20 |
Weight |
801mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2005 |
Series |
74HC |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Type |
D-Type |
Subcategory |
FF/Latches |
Packing Method |
TAPE AND REEL |
Technology |
CMOS |
Voltage - Supply |
2V~6V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Supply Voltage |
4.5V |
Base Part Number |
74HC273 |
Function |
Master Reset |
Output Type |
Non-Inverted |
Number of Elements |
1 |
Polarity |
Non-Inverting |
Supply Voltage-Max (Vsup) |
6V |
Power Supplies |
2/6V |
Supply Voltage-Min (Vsup) |
2V |
Number of Channels |
8 |
Load Capacitance |
50pF |
Number of Bits |
8 |
Clock Frequency |
78MHz |
Propagation Delay |
135 ns |
Quiescent Current |
8μA |
Turn On Delay Time |
18 ns |
Family |
HC/UH |
Logic Function |
D-Type, Flip-Flop |
Current - Output High, Low |
5.2mA 5.2mA |
Max I(ol) |
0.004 A |
Max Propagation Delay @ V, Max CL |
23ns @ 6V, 50pF |
Trigger Type |
Positive Edge |
Input Capacitance |
7pF |
fmax-Min |
24 MHz |
Clock Edge Trigger Type |
Positive Edge |
Height |
2.642mm |
Length |
13.01mm |
Width |
7.595mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MM74HC273WMX Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). D flip flop is included in the Tape & Reel (TR)package. The output it is configured with uses Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountmounts this electrical part. With a supply voltage of 2V~6V volts, it operates. -40°C~85°C TAis the operating temperature. This electronic flip flop is of type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. You should not exceed 78MHzin the output frequency of the device. A total of 1elements are contained within it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. D latch belongs to the 74HC273 family. An input voltage of 4.5Vpowers the D latch. Its input capacitance is 7pFfarads. This D flip flop belongs to the family of HC/UH. Electronic part Surface Mountis mounted in the way. There are 20pins on it. Its clock edge trigger type is Positive Edge. This part is included in FF/Latches. There are 8bits in its design. Vsup reaches its maximum value at 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. In order for the device to operate, it requires 2/6V power supplies. It consumes 8μA current. There are 8 channels available.
MM74HC273WMX Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
MM74HC273WMX Applications
There are a lot of ON Semiconductor MM74HC273WMX Flip Flops applications.
- Data transfer
- Power down protection
- Common Clocks
- Bounce elimination switch
- Circuit Design
- Control circuits
- Asynchronous counter
- Count Modes
- Registers
- 2 – Bit synchronous counter