MIC2026-1YM
| Parameters | |
|---|---|
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e4 |
| Feature | Slew Rate Controlled, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 90mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 1.25A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MIC2026 |
| Number of Outputs | 2 |
| Output Voltage | 6V |
| Output Type | N-Channel |
| Max Output Current | 500mA |
| Interface | On/Off |
| Nominal Supply Current | 5μA |
| Output Configuration | High Side |
| Output Current | 500mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 5 ms |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, UVLO |
| Turn On Time | 5000 μs |
| Output Peak Current Limit-Nom | 0.9A |
| Rds On (Typ) | 90m Ω |
| Drain to Source Resistance | 140mOhm |
| Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Ambient Temperature Range High | 85°C |
| Height | 1.73mm |
| Length | 5mm |
| Width | 3.99mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MIC2026-1YM Overview
It's?packaged?in?the way?of?a?Tube.Package 8-SOIC (0.154, 3.90mm Width) contains it.The lighting driver has the mounting type Surface Mount.The switch type is General Purpose.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.It is possible to use 2 outputs in the lighting driver.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.A lighting driver with Slew Rate Controlled, Status Flag features is available.As you can see, it comes from the MIC2026 family.It contains 8 terminations.The operation is performed through the 8 pins.Currently, the lighting driver has a total of 1 functions.This results in the maximum output current dropping to 500mA to meet the operation criteria.A supply voltage of 5V leads to high efficiency.It is positioned in the direction of Surface Mount.Currently, the LED driving board has 90mOhm resistance.In this case, the output current is set to 500mA.Its maximum input voltage is 5.5V volts.The input voltage minimum is 2.7V volts.
MIC2026-1YM Features
Supplied from 5V
Resistance of 90mOhm
MIC2026-1YM Applications
There are a lot of Microchip Technology MIC2026-1YM Power Switches ICs applications.
- Telecom and Network Systems
- Wireless/Networking Cards
- Portable GPS Device
- Smart Phones, Feature Phones
- Storage Drives
- Portable GPS
- Smartphone and PDA
- Wireless Modem Data Cards
- PC Card Hot Swap
- Wireless Headsets