MCP6482-E/MS

MCP6482-E/MS

2 Channels 12mA per Channel 1pA 65 dB Instrumentational OP Amps 2.2V~5.5V ±1.1V~2.75V MCP6482 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)


  • Manufacturer: Microchip Technology
  • Origchip NO: 536-MCP6482-E/MS
  • Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
  • Datasheet: PDF
  • Stock: 429
  • Description: 2 Channels 12mA per Channel 1pA 65 dB Instrumentational OP Amps 2.2V~5.5V ±1.1V~2.75V MCP6482 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 7 Weeks
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Number of Pins 8
Operating Temperature -40°C~125°C
Packaging Tube
Published 2013
JESD-609 Code e3
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
ECCN Code EAR99
Terminal Finish Matte Tin (Sn) - annealed
Subcategory Operational Amplifier
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 3V
Terminal Pitch 0.65mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number MCP6482
Output Type Rail-to-Rail
Number of Channels 2
Number of Circuits 2
Nominal Supply Current 240μA
Slew Rate 2.7V/μs
Amplifier Type General Purpose
Common Mode Rejection Ratio 65 dB
Current - Input Bias 1pA
Voltage - Supply, Single/Dual (±) 2.2V~5.5V ±1.1V~2.75V
Output Current per Channel 12mA
Input Offset Voltage (Vos) 1.5mV
Bandwidth 4MHz
Unity Gain BW-Nom 4000 kHz
Voltage Gain 115dB
Power Supply Rejection Ratio (PSRR) 91dB
Supply Voltage Limit-Max 6.5V
Max Frequency 10kHz
Height 950μm
Length 3mm
Width 3mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status ROHS3 Compliant

MCP6482-E/MS Overview


A 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. Linear amplifier is delivered in a Tube case. During the past two weeks, there have been close to 8 terminations. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. Instrumentation amplifier is a part of Operational Amplifier. There are 8 pins on this chip. In terms of input offset voltage, operational amplifier rates 1.5mV. This electrical part should be mounted using type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . Maintain 115dB as the voltage gain. There are 2 circuits on this op amp. Instrumentation amplifier has 2 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer.

MCP6482-E/MS Features


supply voltage of 3V
115dB voltage gain
Output Type: Rail-to-Rail

MCP6482-E/MS Applications


There are a lot of Microchip Technology MCP6482-E/MS Instrumentational OP Amps applications.

  • Medical imaging
  • pH (acidity)
  • Band-pass filter
  • Wireless base stations
  • High/low-pass filter circuit
  • Oscilloscopes
  • Power generator
  • Proportional counter tubes
  • High gain DC amplifier
  • Subtraction operation circuits

Write a review

Note: HTML is not translated!
    Bad           Good