MCP6032-E/MS
| Parameters | |
|---|---|
| Factory Lead Time | 14 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MCP6032 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 900nA |
| Nominal Supply Current | 900nA |
| Output Current | 23mA |
| Slew Rate | 0.004V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 23mA |
| Input Offset Voltage (Vos) | 150μV |
| Bandwidth | 10 kHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 115dB |
| Average Bias Current-Max (IIB) | 0.005μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 1kHz |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Height | 950μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MCP6032-E/MS Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. It comes in a Tube case, which protects instrumentation amplifier from damage during delivery. It is estimated that there will be 8 terminations in the next few months. A total of 8 pins are attached to buffer op amp. The linear amplifier should be run at 1.8V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. An 8-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 150μV. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. An 900nA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 115dB. The op amp ic has 2 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer.
MCP6032-E/MS Features
8 Pins
supply voltage of 1.8V
115dB voltage gain
Output Type: Rail-to-Rail
MCP6032-E/MS Applications
There are a lot of Microchip Technology MCP6032-E/MS Instrumentational OP Amps applications.
- Proportional operation circuits
- Oscilloscopes
- Fission chambers
- High/low-pass filter circuit
- Broadcasting
- Portable media players
- Blood pressure sensors
- Signal operation
- Weak signal detection
- Integrator circuits