MC74VHCT574ADT
| Parameters | |
|---|---|
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74VHCT |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| JESD-30 Code | R-PDSO-G20 |
| Function | Standard |
| Qualification Status | COMMERCIAL |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Ports | 2 |
| Clock Frequency | 130MHz |
| Family | AHCT/VHCT |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Output Polarity | TRUE |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.4ns @ 5V, 50pF |
MC74VHCT574ADT Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). A package named Tubeincludes it. T flip flop uses Tri-State, Non-Invertedas its output configuration. It is configured with the trigger Positive Edge. This electronic part is mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. It is at -40°C~85°C TAdegrees Celsius that the system is operating. D-Typeis the type of this D latch. The 74VHCTseries comprises this type of FPGA. It should not exceed 130MHzin terms of its output frequency. D latch consists of 1 elements. During its operation, it consumes 4μA quiescent energy. There are 20 terminations,The power source is powered by 5V. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the AHCT/VHCTfamily. As soon as 5.5Vis reached, Vsup reaches its maximum value. Keeping the supply voltage (Vsup) above 4.5V is necessary for normal operation. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line.
MC74VHCT574ADT Features
Tube package
74VHCT series
MC74VHCT574ADT Applications
There are a lot of Rochester Electronics, LLC MC74VHCT574ADT Flip Flops applications.
- ESCC
- Frequency division
- Power down protection
- Latch
- Functionally equivalent to the MC10/100EL29
- Load Control
- Bus hold
- Communications
- Divide a clock signal by 2 or 4
- Control circuits