MC74HCT374ADTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HCT374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 31 ns |
| Turn On Delay Time | 31 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 31ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74HCT374ADTR2 Overview
The item is packaged in 20-TSSOP (0.173, 4.40mm Width)cases. A package named Tape & Reel (TR)includes it. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. The electronic part is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. A temperature of -55°C~125°C TAis considered to be the operating temperature. This D latch has the type D-Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. This D flip flop should not have a frequency greater than 30MHz. The element count is 1 . There is 4μA quiescent consumption. Currently, there are 20 terminations. It is a member of the 74HCT374 family. It is powered by a voltage of 5V . JK flip flop input capacitance is 10pF farads. HCTis the family of this D flip flop. It is mounted by the way of Surface Mount. A total of 20pins are provided on this board. In this device, the clock edge trigger type is Positive Edge. It is included in FF/Latches. The flip flop is designed with 8bits. In order to achieve its superior flexibility, 8 circuits are used. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. A total of 5V power supplies are needed to run it. The D flip flop has no ports embedded. Optimal efficiency requires a supply voltage of 5V. There are no output lines on the JK flip flop.
MC74HCT374ADTR2 Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT374ADTR2 Applications
There are a lot of ON Semiconductor MC74HCT374ADTR2 Flip Flops applications.
- Clock pulse
- Single Up Count-Control Line
- Registers
- 2 – Bit synchronous counter
- ESD protection
- ESD performance
- Event Detectors
- Divide a clock signal by 2 or 4
- Computers
- Counters