MC74HC74ADTR2G
| Parameters | |
|---|---|
| Factory Lead Time | 45 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 35MHz |
| Propagation Delay | 160 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 17 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 17ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5.1mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HC74ADTR2G Overview
The flip flop is packaged in a case of 14-TSSOP (0.173, 4.40mm Width). A package named Tape & Reel (TR)includes it. In the configuration, Differentialis used as the output. The trigger configured with it uses Positive Edge. Surface Mountmounts this electrical part. A 2V~6Vsupply voltage is required for it to operate. A temperature of -55°C~125°C TAis used in the operation. This D latch has the type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. You should not exceed 35MHzin the output frequency of the device. There have been 14 terminations. It is a member of the 74HC74 family. It is powered from a supply voltage of 3V. Input capacitance of this device is 10pF farads. A device of this type belongs to the family of HC/UH. There is an electronic component mounted in the way of Surface Mount. 14pins are included in its design. In this device, the clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be above 2V. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. Its output current of 5.2mAallows for maximum design flexibility. It operates with 1 output lines. There is a consumption of 2μAof quiescent current from it. 2 channels are available.
MC74HC74ADTR2G Features
Tape & Reel (TR) package
74HC series
14 pins
MC74HC74ADTR2G Applications
There are a lot of ON Semiconductor MC74HC74ADTR2G Flip Flops applications.
- Counters
- Bounce elimination switch
- Storage Registers
- Control circuits
- Shift registers
- ATE
- Cold spare funcion
- 2 – Bit synchronous counter
- Memory
- Guaranteed simultaneous switching noise level