MC10EP52DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 10EP |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 10EP52 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 380 ps |
| Turn On Delay Time | 330 ps |
| Family | 10E |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 4000000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC10EP52DTR2 Overview
The package is in the form of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). It is contained within the Tape & Reel (TR)package. Currently, the output is configured to use Differential. In the configuration of the trigger, Positive, Negativeis used. It is mounted in the way of Surface Mount. A voltage of -3V~-5.5Vis required for its operation. It is at -40°C~85°C TAdegrees Celsius that the system is operating. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 10EP series. This D flip flop should not have a frequency greater than 3GHz. T flip flop consumes 45mA quiescent energy. A total of 8terminations have been recorded. Members of the 10EP52family make up this object. The D flip flop is powered by a voltage of 3.3V . Devices in the 10Efamily are electronic devices. In this case, the electronic component is mounted in the way of Surface Mount. The 8pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. The part is included in FF/Latches. The flip flop is designed with 1bits. Vsup reaches its maximum value at 5.5V. It is imperative that the supply voltage (Vsup) is maintained above 3Vin order to ensure normal operation. The superior flexibility of this product is achieved by using 1 circuits. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. There are -5.2V power supplies attached to it. NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5Vis also one of its characteristics. It is set to -50mAfor the high level output current. There is no low level output current set at 50mA.
MC10EP52DTR2 Features
Tape & Reel (TR) package
10EP series
8 pins
1 Bits
-5.2V power supplies
MC10EP52DTR2 Applications
There are a lot of ON Semiconductor MC10EP52DTR2 Flip Flops applications.
- Clock pulse
- Test & Measurement
- ATE
- High Performance Logic for test systems
- 2 – Bit synchronous counter
- Control circuits
- Cold spare funcion
- Individual Asynchronous Resets
- Frequency division
- Data transfer