MC10EP52DTG
| Parameters | |
|---|---|
| Factory Lead Time | 4 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| Series | 10EP |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP52 |
| Function | Standard |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Output Current | 50mA |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 410 ps |
| Turn On Delay Time | 330 ps |
| Family | 10E |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Halogen Free | Halogen Free |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 4000000000Hz |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC10EP52DTG Overview
The flip flop is packaged in a case of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). As part of the package Tube, it is embedded. This output is configured with Differential. Positive, Negativeis the trigger it is configured with. It is mounted in the way of Surface Mount. Powered by a -3V~-5.5Vvolt supply, it operates as follows. It is operating at a temperature of -40°C~85°C TA. This logic flip flop is classified as type D-Type. In terms of FPGAs, it belongs to the 10EP series. This D flip flop should not have a frequency greater than 3GHz. It consumes 45mA of quiescent current without being affected by external factors. There are 8 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 10EP52 family contains it. The D flip flop is powered by a voltage of 3.3V . It is a member of the 10Efamily of D flip flop. Surface Mount mounts this electronic component. As you can see from the design, it has pins with 8. This device exhibits a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. The design is based on 1bits. The maximal supply voltage (Vsup) reaches 5.5V. For normal operation, the supply voltage (Vsup) should be above 3V. Its flexibility is enhanced by 1 circuits. Due to its reliability, this T flip flop is well suited for RAIL. The power supply is -5.2V. The 50mA output current allows it to be designed with the greatest amount of flexibility. NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5Vis also one of its characteristics. In this case, the high level output current is set to -50mA. In the low level output current setting, the current is set to 50mA.
MC10EP52DTG Features
Tube package
10EP series
8 pins
1 Bits
-5.2V power supplies
MC10EP52DTG Applications
There are a lot of ON Semiconductor MC10EP52DTG Flip Flops applications.
- Divide a clock signal by 2 or 4
- Latch-up performance
- CMOS Process
- Automotive
- Cold spare funcion
- Storage Registers
- Set-reset capability
- Control circuits
- Pattern generators
- Supports Live Insertion