MC10EP51DG
| Parameters | |
|---|---|
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 4 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| Series | 10EP |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP51 |
| Function | Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 370 ps |
| Turn On Delay Time | 320 ps |
| Family | 10E |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Halogen Free | Halogen Free |
| Prop. Delay@Nom-Sup | 0.42 ns |
| Trigger Type | Positive, Negative |
MC10EP51DG Overview
As a result, it is packaged as 8-SOIC (0.154, 3.90mm Width). The Tubepackage contains it. Currently, the output is configured to use Differential. This trigger is configured to use Positive, Negative. Surface Mountmounts this electrical part. The JK flip flop operates with an input voltage of -3V~-5.5V volts. A temperature of -40°C~85°C TAis considered to be the operating temperature. This electronic flip flop is of type D-Type. The 10EPseries comprises this type of FPGA. Its output frequency should not exceed 3GHz Hz. As a result, it consumes 45mA quiescent current. There are 8 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This D latch belongs to the family of 10EP51. A voltage of 3.3V is used as the power supply for this D latch. The electronic device belongs to the 10Efamily. The electronic part is mounted in the way of Surface Mount. There are 8pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device is part of the FF/Latchesbase part number family. There are 1bits in its design. It reaches the maximum supply voltage (Vsup) at 5.5V. Normally, the supply voltage (Vsup) should be kept above 3V. The superior flexibility of this product is achieved by using 1 circuits. This D flip flop is well suited for RAIL based on its reliable performance. An electrical current of -5.2V volts is applied to it. As an additional reference, you may refer to electronic flip flop NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V. In this case, the high level output current is set to -50mA. 50mAis set as the low level output current.
MC10EP51DG Features
Tube package
10EP series
8 pins
1 Bits
-5.2V power supplies
MC10EP51DG Applications
There are a lot of ON Semiconductor MC10EP51DG Flip Flops applications.
- Data transfer
- Data storage
- Bounce elimination switch
- Frequency Dividers
- Functionally equivalent to the MC10/100EL29
- Reduced system switching noise
- Set-reset capability
- Divide a clock signal by 2 or 4
- Matched Rise and Fall
- Communications