MAX894LESA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Base Part Number | MAX894 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Voltage | 5V |
| Output Type | P-Channel |
| Max Output Current | 500mA |
| Operating Supply Voltage | 5.5V |
| Input Voltage-Nom | 3V |
| Interface | On/Off |
| Analog IC - Other Type | DUAL SWITCHING CONTROLLER |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 200 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Number of Inputs | 1 |
| Max Input Voltage | 5.5V |
| Supply Current-Max (Isup) | 0.05mA |
| Turn-Off Delay Time | 20 μs |
| Switcher Configuration | SINGLE |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Adjustable), Over Temperature |
| Rds On (Typ) | 120m Ω |
| Drain to Source Resistance | 120mOhm |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX894LESA Overview
The LED driver's packaged as a Tube.The 8-SOIC (0.154, 3.90mm Width) package contains it.This LED driving board is mounted using the mounting type Surface Mount.There is a General Purpose switch type associated with it.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.There is a default setting of 2 for output.To operate, it needs a supply voltage of Not Required.A maximum output voltage of P-Channel volts can be achieved by this LED driver.It belongs to the MAX894 family.A total of 8 terminations can be found in it.The operation is carried out using the 8 pins.Currently, there are 1 functions associated with the lighting driver.The maximum output current is reduced to 500mA to meet the operation criteria.Surface Mount is mounted in the way.A total of 8 pins are present on it.It has 300mOhm resistance.In this case, a digital IC is used, which is DUAL SWITCHING CONTROLLER.It is recommended that the supply voltage be set at 5.5V in order to achieve maximum efficiency.It has a maximum input voltage of 5.5V volts.There is a minimum input voltage of 2.7V volts for this LED driver.In order to operate, it requires at most 0.05mA amps of supply current.Currently, there are 1 inputs available.
MAX894LESA Features
Resistance of 300mOhm
MAX894LESA Applications
There are a lot of Maxim Integrated MAX894LESA Power Switches ICs applications.
- Hot-Swap Systems
- Various applications equipped with buttons
- USB Protection
- Portable GPS Device
- Set-Top Boxes
- PC Card Hot Swap
- HDD and SSD
- Solid State Drivers
- Storage (HDDs, SSDs)
- Wearable Devices