MAX4760AEBX+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 36-WFBGA, CSPBGA |
| Number of Pins | 36 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 36 |
| Resistance | 3.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 2.105W |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Number of Functions | 4 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4760 |
| Output | SEPARATE OUTPUT |
| Pin Count | 36 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 12μA |
| Turn On Delay Time | 800 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 800 ns |
| -3db Bandwidth | 150MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 800ns, 800ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.67mm |
| Length | 3.06mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4760AEBX+T Overview
Due to its 36-WFBGA, CSPBGA packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. There is 2:2 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Totally, there are 36 terminations. A electrical component with 2 channels is capable of high-quality output. Powered by a 2.7V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 36 series. These analog multiplexers are built based on DPDT switching circuits. 4 circuits are used in this analogue multiplexer. MAX4760 can be used to search for analog multiplexer variants. It has an internal resistance of 3.5Ohm. For functions related to 36 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. 1.8V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 1μA. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4760AEBX+T Features
2 Channels
Switch Circuit: DPDT
1μA Supply Current
-3db Bandwidth: 150MHz
MAX4760AEBX+T Applications
There are a lot of Maxim Integrated MAX4760AEBX+T Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- High speed data transmission line cards
- USB 1.1 signal switching circuits
- Communication systems
- Cable PC
- DVD-R
- Channelized and Unchannelized DS3 applications
- Multi-Line E1 Interface Cards
- FTTH
- Fault Tolerant Systems