MAX4732EUA+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4732 |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 11V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 85ns, 45ns |
| Charge Injection | 7.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -108dB @ 1MHz |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 2V~11V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
MAX4732EUA+ Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. Total terminations are 8. As a result of its 1 channels, this electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. This multiplexer is composed of 2 circuits. Try searching with MAX4732 if you're looking for variants. Using a single voltage supply, this switch device consumes 2V~11V volts.
MAX4732EUA+ Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 300MHz
MAX4732EUA+ Applications
There are a lot of Maxim Integrated MAX4732EUA+ Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Battery-powered systems
- SONET/SDH ADM
- Transmit
- Multi-Line E1 Interface Cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Data Acquisition Systems
- PBXs
- Battery Powered Instruments
- PBX interfaces