Parameters |
Factory Lead Time |
6 Weeks |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2004 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
25Ohm |
Terminal Finish |
Matte Tin (Sn) |
Additional Feature |
CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
457mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4712 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
11V |
Min Supply Voltage |
2.7V |
Max Supply Current |
75μA |
Throw Configuration |
SPST |
Turn On Delay Time |
125 ns |
Voltage - Supply, Single/Dual (±) |
2.7V~11V ±2.7V~5.5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
80 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
25Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
59 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
8pF 8pF |
On-state Resistance Match-Nom |
0.2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
125ns, 80ns |
Charge Injection |
25pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Crosstalk |
-87dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height |
950μm |
Length |
5.1mm |
Width |
4.5mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
MAX4712EUE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SPST - NO switching circuits. A total of 4 circuits make up this switch device. MAX4712 can be used to search for analog multiplexer variants. An switch multiplexer with 25Ohm internal resistance has a value of 25Ohm. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 11V voltage to the switch device. Analog switch ics with Dual, Single supply type are cost-effective. 2.7V is the lowest voltage the electrical component should receive. Put voltage above 75μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 5.5V. A dual power supply should have at least 2.7V voltage attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Check out the electrical component's additional features, such as the following: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V.
MAX4712EUE+ Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V
MAX4712EUE+ Applications
There are a lot of Maxim Integrated MAX4712EUE+ Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Precision instrumentation
- PDAs
- ATM
- Wireless Local Loop
- SONET
- Imaging
- PCMCIA cards
- SDH/SONET multiplexers
- Microwave transmission systems