MAX4626EUK+T
| Parameters | |
|---|---|
| Off-state Isolation-Nom | 51 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 65pF 65pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 50ns, 30ns |
| Charge Injection | 40pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 500mOhm |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2.9mm |
| Width | 1.63mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 29.993795mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 500mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4626 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 50 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
MAX4626EUK+T Overview
Due to its SC-74A, SOT-753 packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. 5 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 5 pins. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with MAX4626. A 500mOhm internal resistance characterizes this multiplexer. To find out what the functions of 5 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The digital multiplexer has a low cost Single supply. There should be 1.8V voltage fed to the electrical part below 1.8V. In order to operate this switch device, it would need a current of 10μA. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 10μA. 5V operating voltages can be used with this electrical part. It has a Drain to Source resistance of 500mOhm ohms.
MAX4626EUK+T Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
Drain-to-Source resistance: 500mOhm
MAX4626EUK+T Applications
There are a lot of Maxim Integrated MAX4626EUK+T Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Communications systems
- Data Acquisition Systems
- Microprocessor controlled systems
- MP3 players
- Fault Tolerant Systems
- Industrial and process control systems
- Optical Applications
- Residential Gateways, Home Gateway/Router
- Avionics and Military Systems