MAX4624EZT+T
| Parameters | |
|---|---|
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 32pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 50ns |
| Charge Injection | 65pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -57dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 3Ohm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 1Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4624 |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Max Supply Current | 10μA |
| Number of Bits | 2 |
| Turn On Delay Time | 50 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 1Ohm |
| High Level Output Current | 200mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
MAX4624EZT+T Overview
This electronic part is conveniently packaged in SOT-23-6 Thin, TSOT-23-6, making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operational temperature extended around -40°C~85°C TA. In total, there are 6 terminations. By its 1 channels, the electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. As part of its design, the 6 series is equipped with this electronic component. Circuits based on SPDT switching are used to construct these analog switch ics. A total of 1 circuits make up this switch device. Using the MAX4624 search parameter, you can discover variants of the switch. There is 1Ohm internal resistance in this digital multiplexer. The functions of 6 pins can be found in the datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. Putting voltage greater than 10μA on the multiplexer may cause damage. Drain to Source resistance for this electronic component is 3Ohm. The switch device is capable of conducting in a 2-bit mode.
MAX4624EZT+T Features
1 Channels
Switch Circuit: SPDT
Drain-to-Source resistance: 3Ohm
2-Bit
MAX4624EZT+T Applications
There are a lot of Maxim Integrated MAX4624EZT+T Analog Switches & Multiplexers ICs applications.
- Industrial
- Sample hold systems
- Industrial and process control systems
- Access Concentrators
- Avionics and Military Systems
- High-Voltage
- PBXs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Residential Gateways, Home Gateway/Router
- Digital cross connects (DSX-1)