MAX4597DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4597 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 83 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4597DBVR Overview
Shipping overseas is convenient due to the electrical component's packing in SC-74A, SOT-753. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. Total terminations are 5. A high-quality output is provided by the electrical component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. A key feature of the 5 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with MAX4597. A 10Ohm internal resistance characterizes this multiplexer. Datasheets for 5 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 2V as the lowest voltage for the electrical part. An operating current of 1μA would be sufficient for this switch device. An analogue multiplexer drains from a single voltage supply at 2.4V~5.5V. A voltage higher than 1μA may cause damage to the switch multiplexer. 300MHz bandwidths enable data to be transferred.
MAX4597DBVR Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
Bandwidth: 300MHz
MAX4597DBVR Applications
There are a lot of Texas Instruments MAX4597DBVR Analog Switches & Multiplexers ICs applications.
- DSLAMs
- RGB switches
- PBX interfaces
- Sample-and-hold systems
- Cellular phones
- PCMCIA cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Fiber In The Loop (FITL)
- USB 1.1 signal switching circuits
- Audio and video routing