MAX4596DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX4596 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 83 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4596DBVR Overview
Shipping overseas is convenient due to the electrical component's packing in SC-74A, SOT-753. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there are 5 terminations. A high-quality output is provided by the electrical component's 1 channels. A 3V voltage supply should turn on and run the electronic component. A total of 5 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching with MAX4596 to find analog multiplexer variants. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. To find out what the 5 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 2V. For this multiplexer to operate, 1μA current would be sufficient. This analog switch requires a voltage of 2.4V~5.5V to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. This switch operates within the bandwidth of 300MHz.
MAX4596DBVR Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Bandwidth: 300MHz
MAX4596DBVR Applications
There are a lot of Texas Instruments MAX4596DBVR Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Communications systems
- PCMCIA cards
- Remote wireless modules
- New designs requiring multiplexer functions
- Video switching
- E1 Network Equipment
- SDH
- Transmit
- Imaging