MAX4593CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 12V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4593 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | 12/15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 45ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -85dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~16V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX4593CSE+ Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around 0°C~70°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. With a 12V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. A SPST - NO/NC switching circuit is used to build these analog multiplexers. It consists of 4 circuits. Try searching with MAX4593 to find analog multiplexer variants. There is 20Ohm internal resistance in this digital multiplexer. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 16V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. 3V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1μA would be sufficient for this switch device. An analogue multiplexer drains from a single voltage supply at 3V~16V. When the digital multiplexer is charged above 1μA, damage can occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
MAX4593CSE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX4593CSE+ Applications
There are a lot of Maxim Integrated MAX4593CSE+ Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- Audio and video routing
- Optical Applications
- Industrial
- Relay replacements
- Precision test equipment
- Switching Systems
- Precision instrumentation
- Medical systems
- Routers