MAX4561EUT-T
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4561 |
| Pin Count | 6 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 50nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Turn On Delay Time | 150 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 80 ns |
| On-State Resistance (Max) | 70Ohm |
| High Level Output Current | 10mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 80ns |
| Charge Injection | 17pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~12V |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Weight | 36.003894mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Additional Feature | CAN ALSO OPERATE WITH 3V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
MAX4561EUT-T Overview
Due to its SOT-23-6 packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 6. A 1 channel electronic part produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. Circuits based on SPDT switching are used to construct these analog switch ics. There are 1 circuits in this multiplexer. Search with MAX4561 if you are looking for analog multiplexer variants. A 70Ohm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 1.8V. For this multiplexer to operate, 50nA current would be sufficient. A voltage of 1.8V~12V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. Additional features include: CAN ALSO OPERATE WITH 3V SUPPLY. It conducts in a 4-bit manner.
MAX4561EUT-T Features
1 Channels
Switch Circuit: SPDT
50nA Supply Current
Additional Features: CAN ALSO OPERATE WITH 3V SUPPLY
4-Bit
MAX4561EUT-T Applications
There are a lot of Maxim Integrated MAX4561EUT-T Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Audio and video signal routing
- MP3 players
- Data switching
- USB 1.1 signal switching circuits
- Audio signal routing
- New designs requiring multiplexer functions
- Cellular phones
- Optical Applications
- DSLAMs