MAX4542EKA-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-8 |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4542 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NC |
| Height Seated (Max) | 1.45mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4542EKA-T Overview
Due to its SOT-23-8 packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 8 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. A 5V voltage supply should turn on and run the electronic component. As part of the design of the 8 series, this electronic part has been incorporated into the system. A SPST - NC switching circuit is used to build these analog multiplexers. 2 circuits are used in this analogue multiplexer. Use MAX4542 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 60Ohm. The functions of 8 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. This analog switch ic utilizes SEPARATE OUTPUT output.
MAX4542EKA-T Features
1 Channels
Switch Circuit: SPST - NC
MAX4542EKA-T Applications
There are a lot of Maxim Integrated MAX4542EKA-T Analog Switches & Multiplexers ICs applications.
- RGB switches
- Data Acquisition Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- SDH/SONET multiplexers
- Mechanical reed relay replacement
- Sample hold systems
- Channelized and Unchannelized DS3 applications
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- DVD-R
- DSUs