MAX4541CSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4541 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Polarity | Non-Inverting |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 10mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 100ns |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4541CSA+T Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Around 0°C~70°C TA is the extended operating temperature. 8 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. It is injected into the electrical part body with 8 pins. Unlike digital switches, these are based on SPST - NO switching circuits. There are 2 circuits in this multiplexer. Try searching for the analog switch ic with MAX4541 if you are looking for variants. It has an internal resistance of 60Ohm. Datasheets for functions of 8 pins are available. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. Analogue multiplexer with a Single supply type that is cost-effective. 2.7V is the lowest voltage the electrical component should receive. This multiplexer would work with 100pA current. An analogue multiplexer drains from a single voltage supply at 2.7V~12V. The analogue multiplexer may be damaged if voltage is greater than 1μA. It can operate from 9V operating voltages.
MAX4541CSA+T Features
1 Channels
Switch Circuit: SPST - NO
100pA Supply Current
MAX4541CSA+T Applications
There are a lot of Maxim Integrated MAX4541CSA+T Analog Switches & Multiplexers ICs applications.
- MP3 players
- Digital access cross connects
- Cell phones
- Isolation
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Microprocessor Controlled Analog Systems
- Precision data acquisition
- Wireless Local Loop
- High reliability control systems
- PBXs