MAX4515EPA
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4515 |
| Pin Count | 8 |
| JESD-30 Code | R-PDIP-T8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
MAX4515EPA Overview
As the electronic part is packed in 8-DIP (0.300, 7.62mm), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Through Hole position. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. In total, there are 8 terminations. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 8 series. Multiplexers built on a SPST - NC switching circuit are built. A total of 1 circuits make up this switch device. Try searching with MAX4515 to find analog multiplexer variants. The analog multiplexer shown here is a typical Multiplexer or Switches. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply.
MAX4515EPA Features
1 Channels
Switch Circuit: SPST - NC
MAX4515EPA Applications
There are a lot of Maxim Integrated MAX4515EPA Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Switching Systems
- RGB switches
- Multi-Line E1 Interface Cards
- E1 Multiplexer
- Medical systems
- PCMCIA cards
- Industrial control systems