MAX4515CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4515 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4515CSA Overview
The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around 0°C~70°C TA is the extended operating temperature. A total of 8 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 8 series. A SPST - NC switching circuit is used to build these analog multiplexers. 1 circuits are used in this analogue multiplexer. Try searching with MAX4515 to find analog multiplexer variants. It has an internal resistance of 10Ohm. For details about the functions of 8 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 12V. Single supply type digital switch with a low cost. There should be 2V voltage fed to the electrical part below 2V. The analogue multiplexer could operate on 2μA current. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. There is a voltage range of 9V operating voltages for the electrical part.
MAX4515CSA Features
1 Channels
Switch Circuit: SPST - NC
2μA Supply Current
MAX4515CSA Applications
There are a lot of Maxim Integrated MAX4515CSA Analog Switches & Multiplexers ICs applications.
- Industrial
- Audio signal routing
- Precision instrumentation
- Channelized and Unchannelized DS3 applications
- Residential Gateways, Home Gateway/Router
- ATM
- USB 1.1 signal switching circuits
- Avionics and Military Systems
- Medical
- Data Acquisition Systems